loading

PRANCE metalwork là nhà sản xuất hàng đầu về hệ thống trần và mặt tiền bằng kim loại.

Sản phẩm
Sản phẩm

Are aluminum ceiling systems compliant with seismic regulations?

Are aluminum ceiling systems compliant with seismic regulations? 1

Yes, aluminum ceiling systems can be designed and installed to be fully compliant with seismic regulations in earthquake-prone areas. However, compliance is not inherent to the panels themselves but depends on the design and installation of the entire suspension system according to local building codes and standards (e.g., IBC, ASCE 7, ASTM E580). Requirements vary based on the project's location and assigned Seismic Design Category (SDC), which ranges from A (low seismic risk) to F (very high seismic risk).


For areas with moderate to high seismic requirements (typically SDC C, D, E, F), specific measures are mandatory:


Grid System: Intermediate or heavy-duty T-bar grid systems meeting seismic load requirements must be used.


Connections: Main runners and cross tees need secure connections.


Perimeter Clearance: A minimum clearance (often 3/4 inch) must be maintained between the grid ends/panels and the perimeter walls to allow for movement. Heavy-duty wall angle molding is often required.


Hold-Down Clips: Panels, including our aluminum ones, may require hold-down clips, especially near the perimeter, to prevent them from dislodging.


Lateral Bracing: The grid system must be braced against lateral movement using vertical hanger wires splayed in opposing directions or rigid compression posts at specified intervals. The frequency and type of bracing depend on the SDC and ceiling area.


Our lightweight aluminum panels can actually be advantageous in seismic designs as they impose less dead load on the suspension system. It's crucial that the ceiling system is designed by qualified professionals referencing the specific code requirements for the project's SDC.


Đề nghị cho bạn
Thú vị?
Yêu cầu cuộc gọi từ chuyên gia
Giải pháp hoàn hảo dành riêng cho trần kim loại của bạn & công trình tường. Nhận giải pháp hoàn chỉnh cho trần kim loại tùy chỉnh & công trình tường. Nhận hỗ trợ kỹ thuật về trần kim loại & thiết kế, lắp đặt tường & điều chỉnh.
Giải pháp kiến ​​trúc
Được thiết kế riêng cho bạn
Các loại bề mặt hoàn thiện và bảng màu
Contact Info
Điện thoại: +86-757-83138155
Điện thoại/WhatsApp: +86-13809708787
Số fax: +86-757-83139722

Nhà máy và phòng trưng bày: Số 169, Khu phía Nam, Khu công nghiệp điện và điện tử, Baini, Sanshui, Phật Sơn, Quảng Đông.
Bạn có quan tâm đến sản phẩm của chúng tôi không?
Chúng tôi có thể lập bản vẽ lắp đặt riêng cho sản phẩm này theo yêu cầu của bạn. Vui lòng liên hệ với chúng tôi.

*Chúng tôi sẽ trả lời trong vòng 24 giờ. Nếu bạn không nhận được email của chúng tôi, vui lòng kiểm tra thư mục thư rác. Đối với các yêu cầu khẩn cấp, vui lòng liên hệ qua WhatsApp: +86-13809708787

* Vui lòng đảm bảo email và số điện thoại của bạn chính xác để chuyên viên của chúng tôi có thể liên hệ với bạn nhanh chóng, hoặc bạn có thể gửi tin nhắn đến số WhatsApp +86-13809708787

弹窗效果
Customer service