PRANCE metalwork is a leading manufacturer of metal ceiling and facade systems.
Grand lobbies have a sound problem. Hard floors, tall ceilings and glass all bounce noise.
The design brief usually asks for something impressive, stone floors, double height glazing, a feature wall behind reception, and nobody notices the acoustics until the building opens and every footstep, phone call and rolling suitcase echoes around the space, turning a quiet arrival into a noisy one.
Metal can fix that. If it is perforated and backed properly.
Interior metal wall panels can look solid and premium while absorbing a large share of the sound that hits them. The secret sits behind the face.
Perforations let sound pass through the metal face into an absorbent backing behind it, where the sound energy is converted to a small amount of heat.
The metal itself does not absorb much. It is the combination that works.
A typical acoustic build-up has a perforated face, an acoustic fleece bonded to the back, and often a layer of mineral wool or similar absorber in the cavity behind. Sound waves travel through the holes, enter the porous material and lose energy as they move through it.
Well-designed perforated metal wall systems with absorbent backing commonly reach NRC values around 0.60 to 0.90, depending on open area, backing and cavity depth.
NRC, the noise reduction coefficient, is an average of sound absorption across key speech frequencies, measured to ASTM C423 in a reverberation room. A value of 0 means total reflection. A value near 1 means very high absorption.
|
Build-up |
Indicative NRC range |
|
Solid metal panel, no backing |
Close to 0 |
|
Perforated panel with acoustic fleece only |
Lower to moderate |
|
Perforated panel with fleece and mineral wool in cavity |
Moderate to high |
|
Deeper cavity with thicker absorber |
Usually higher, especially at lower frequencies |
These are typical patterns, not guarantees. Ask for tested results for the exact build-up being specified.
Open area drives acoustic performance as much as looks.
Very small open area limits how much sound can reach the backing. Most acoustic metal panels use a perforation pattern with enough open area to let sound through while keeping the face looking refined, and micro perforation can give an almost solid appearance from normal viewing distances.
For metal paneling for interior walls at hand height, smaller holes are also harder to damage and easier to clean.
They work best on large wall areas facing other hard surfaces, especially where reflections bounce between parallel walls or toward seating and reception.
Feature walls behind reception desks
Long walls along circulation routes
Walls opposite large glazed facades
Upper wall zones above hand height in tall spaces
Areas near waiting and seating zones
Ceilings often carry much of the treatment, but walls matter in tall lobbies where the ceiling is far away. An acoustic consultant can model how much treatment is needed to reach a target reverberation time.
Aluminum faces are noncombustible, and complete acoustic panels are commonly tested to ASTM E84 to show their surface burning class.
Interior finish rules in the building code set flame spread classes by occupancy and location, with lobbies and exit routes often needing Class A. The backing and adhesive matter as well as the metal, so check that the test report covers the full panel build-up, not just bare aluminum.
Lobbies take abuse. Luggage hits walls. So do trolleys and cleaning machines, sometimes many times a day, and each knock leaves a mark that the next visitor sees on the way in.
Use a thicker face or impact-resistant zones at low level, choose a durable finish such as powder coat or PVDF, and confirm which cleaning products the coating tolerates. Removable panels make it easy to replace a damaged section without disturbing the rest of the wall. Acoustic fleece behind the face should be protected from moisture and dust.
Usually on a concealed subframe or clip system fixed to the wall, with the cavity behind filled with absorber as required.
Concealed fixings keep the face clean. Clip-on systems allow panels to be removed for access to services. Joint lines should align with doors, glazing and reception joinery so the wall looks planned, not patched.
Acoustic metal walls let a lobby look hard and sound soft.
Choose a perforation with enough open area, back it with tested absorbent layers, place panels where reflections are worst, confirm the fire class of the full build-up and plan for durability at low level. With those steps, the space keeps its grand appearance and loses the echo. These choices also fit within the wider guide to building-type requirements.
Yes, when perforated and backed with acoustic fleece or mineral wool. The perforations let sound reach the absorbent layer behind the metal face.
The noise reduction coefficient is an average sound absorption rating measured to ASTM C423. Higher values mean more absorption.
Many complete panel build-ups are tested to ASTM E84 and reach Class A, but the test report must cover the actual backing and adhesive used.
Usually yes, especially at lower frequencies, because more absorbent material and air space sit behind the perforated face.
With clip-on or removable systems, yes. That makes maintenance much easier in busy public spaces.
*We will reply within 24 hours. If you don't receive our email, please check your spam folder. For urgent inquiries, please reach out via WhatsApp: +86-13809708787
* Kindly ensure your email and phone number are correct so our specialist can reach you promptly, or you can send a message to our whatsapp +86-13809708787