loading

PRANCE metalwork is a leading manufacturer of metal ceiling and facade systems.

Products
Products

Metal Wall Panels for Airports: Jet Wash & Impact Standards

An airport facade faces two audiences. Passengers on one side, aircraft on the other.

The landside elevation has to welcome travelers and carry the architecture, while the airside elevations face engine exhaust, blowing grit, de-icing fluid, fuel residue, baggage tugs, belt loaders and service vehicles that run within meters of the wall all day and much of the night, and the same panel system often has to do both jobs.

Airports punish weak details. Quickly.

Specifying metal wall panels for airports means treating each elevation by its real exposure. We have worked on more than twenty airport projects, and the airside face is almost always where the design gets tested hardest.

Metal Wall Panels for Airports: Jet Wash & Impact Standards 1

What Is Jet Wash and How Does It Affect Airport Wall Panels?

Jet wash, also called jet blast, is the high-velocity exhaust behind aircraft engines, and it can push air, grit and small debris against nearby walls at speeds well above normal design winds.

Most buildings are not placed directly behind engines at high power. But terminals, piers, hangars and service buildings near taxi lanes and stands can see repeated blast as aircraft turn, push back or break away from stands.

Airport planners use guidance such as FAA Advisory Circular 150/5300-13 for airport design, which addresses jet blast effects. Where the facade sits inside a blast zone, the airport authority or its engineers usually set the pressures the wall must resist.

How Should Panels Be Designed Near Jet Blast Zones?

They should be designed for the blast pressures set by the airport engineers, with stronger fixings, closer support spacing and edges detailed so air cannot get behind the panels.

  • Confirm blast velocities or pressures for each affected elevation

  • Check panels, clips and subframe for those loads as well as ASCE 7 wind

  • Avoid open panel edges that face the blast direction

  • Use mechanically fixed trims, not sealant alone

  • Consider debris impact from grit and small stones

Repeated blast is also a fatigue question. Fixings that loosen slowly under thousands of cycles are a common long-term problem.

Impact Resistance for Airside Metal Wall Panels

Ground equipment hits walls. Often.

The lowest two or three meters of airside walls take knocks from tugs, belt loaders, catering trucks and baggage carts. Thicker panels, impact-resistant zones, steel bollards and kerbs all help. Many airports add replaceable low-level panels, so a damaged section can be swapped without disturbing the wall above.

Wall zone

Main risk

Typical response

Ground level airside

Vehicle and equipment impact

Thicker panels, guards, replaceable panels

Mid-height airside

Jet blast and grit

Strong fixings, closed edges

Upper levels

Wind and glare

Engineered support, low-reflectance finishes

Landside entrances

Public contact and branding

Durable finishes, clean joints

Do Architectural Metal Wall Panels Cause Glare at Airports?

They can, so reflective finishes near runways and control towers should be reviewed for glare toward pilots and controllers.

Metal Wall Panels for Airports: Jet Wash & Impact Standards 2

Architectural metal wall panels with high gloss or mirror finishes can reflect sunlight at difficult angles. Lower gloss coatings and textured or perforated surfaces reduce specular reflection. Many airports require glare analysis for new buildings near airfield operations, so finish choice should follow that review rather than come before it.

Airport Panel Finishes That Resist Fuel, De-Icing Fluid and Grime

Airside surfaces get dirty in specific ways.

Exhaust soot, rubber dust, fuel and de-icing fluid all reach the walls. High-performance PVDF coatings to AAMA 2605 resist chemicals and cleaning well, and their color stability suits terminals expected to last decades. Confirm that the coating tolerates the cleaning chemicals the airport actually uses.

Fire, Security and Maintenance Rules for Airport Wall Panels

Terminals are large assembly buildings, so fire rules for exterior walls apply fully, including NFPA 285 where the assembly contains combustible components. Security zones may limit how panels can be removed from outside. Maintenance teams need access for cleaning, inspection and repair without closing stands for long.

Removable panels help inside too. At the Libya International Airport, we engineered a seismic-resistant suspension ceiling where every panel can be removed independently, so no separate inspection hatches were needed, and we used 3D modeling and factory trial installations to confirm the fit before production.

How Airport Metal Panel Projects Handle Shipping and Phasing

Airports are often built while still operating. Deliveries arrive in phases, and panels may wait on site for weeks.

Metal Wall Panels for Airports: Jet Wash & Impact Standards 3

For the Vladivostok International Airport in Russia, our team supplied aluminum open cell ceilings, hanging panels and perforated clip-in systems in a metallic gray finish, and careful packaging and protection were needed because the components traveled a long international route. Planning crates and storage for phased work keeps finishes intact until installation.

Conclusion on Metal Wall Panels for Airports

Airport walls must handle blast, impact, glare and constant cleaning.

Define exposure elevation by elevation, design airside panels and fixings for blast pressures and fatigue, protect low-level zones from equipment, choose low-glare finishes where the airfield requires it, and make panels removable for maintenance. Those steps fit within the wider requirements by building type. Share your terminal drawings with PRANCE and request an airport facade review.

Frequently Asked Questions

1. What is jet blast?

It is the high-velocity exhaust behind aircraft engines. Walls near taxi lanes and stands can be exposed to repeated blast and blown debris.

2. Which guidance covers jet blast at airports?

In the United States, FAA Advisory Circular 150/5300-13 on airport design addresses jet blast. Airport authorities usually set facade blast requirements.

3. How do airports protect walls from ground equipment?

With thicker or reinforced low-level panels, bollards, kerbs and replaceable panels in impact zones.

4. Can metal facades cause glare for pilots?

Yes, reflective finishes can. Glare analysis and low-gloss or textured finishes reduce the risk near airfield operations.

5. Which finish suits airport metal panels?

High-performance PVDF to AAMA 2605 is common, as it resists chemicals, cleaning and weathering well over long service lives.

prev
Metal Wall Panels by Building Type: Codes & Design Guide
Metal Wall Panels for Cold Storage: Vapor Drive & Thermal Breaks
next
recommended for you
Interested?
Request a call from a specialist
Tailor-make profect solutions for your metal ceiling & wall projects. Get a complete solution for customized metal ceiling & wall projects. Receive technical support for metal ceiling & wall design,installation & correction.
Architectural Solutions
Customized For You
Surface Finishes & Color Charts
Contact Info
Tel: +86-757-83138155
Tel/Whatapps: +86-13809708787
Fax: +86-757-83139722

Factory and Showroom: 169, South Area, Base of Electrical and Electronic lndustry, Baini, Sanshui, Foshan, Guangdong.
Are you interested in Our Products?
We can customize installation drawings specifically for this product for you. Please contact us.

*We will reply within 24 hours. If you don't receive our email, please check your spam folder. For urgent inquiries, please reach out via WhatsApp: +86-13809708787

* Kindly ensure your email and phone number are correct so our specialist can reach you promptly, or you can send a message to our whatsapp +86-13809708787

弹窗效果
Customer service