loading

PRANCE metalwork is a leading manufacturer of metal ceiling and facade systems.

Products
Products

What Is a Curtain Wall? How Glass Curtain Walls Work

what is a curtain wall

A continuous glass facade can conceal floor slabs, framing and connections behind a uniform exterior. Two buildings with similar elevations may therefore use different assemblies and construction methods. The appearance tells you little about how the wall is supported or how it controls rainwater.

So, what is a curtain wall? It is a non-load-bearing exterior wall system attached to the building structure. A glass curtain wall uses glass as a principal infill material. This article explains how its components work together and why those relationships matter when reviewing a facade proposal.

What Is a Curtain Wall in Construction? 

Curtain Wall in Construction

A curtain wall is a non-load-bearing exterior wall attached to a building's main structure. Its job is to enclose the building, not support the floors or roof. But it still has to carry its own weight and withstand wind loads, which transfer through the framing and anchors into the structure. That is why curtain walls need structural design even though they are called non-load-bearing.

What appears to be a continuous glass facade usually has a supporting assembly behind it. In a typical aluminum curtain wall, vertical mullions and horizontal transoms form the framing, with glass fitted into the openings. Anchors connect the assembly to the building, while gaskets and sealants help control air and water at the joints.

Not every part of a glass curtain wall is transparent. Vision glass admits light and views, while opaque spandrel areas conceal floor edges and other construction behind the facade. Depending on the system, these areas may use glass, metal panels or other suitable materials.

Even a facade that looks frameless needs support. Structural silicone glazing can reduce visible external caps without eliminating the framing behind the glass. An elevation shows the intended appearance, but a section drawing reveals the supporting construction and the distinction between transparent and opaque areas.

How Does a Glass Curtain Wall Work? 

curtain wall system

A glass curtain wall works by transferring loads from its glass and framing back to the building structure. Anchors provide the connection, while joints, seals and drainage paths accommodate movement and control water and air leakage. The glazing and thermal breaks help manage heat transfer and solar gain. From outside, much of this construction is hidden behind the glass.

How Curtain Wall Connections Handle Loads and Movement 

When wind presses against the glass, the load passes into the curtain wall framing. Mullions and transoms transfer it through anchors fixed to floor slabs, columns or other structural supports. The glass's own weight is carried by glazing supports into the framing and then to the building structure.

Larger glass panes can create fewer visible divisions, but the change also affects what sits behind the glass. Panel dimensions influence glass requirements, mullion sizing and connection design. A larger pane may need a different frame configuration, so review proposed glass sizes with the system supplier before finalizing the facade elevation.

Buildings move under service conditions, and aluminum expands and contracts with temperature. Curtain wall joints and connections must accommodate these movements rather than restrain them everywhere. Making every connection rigid is not necessarily better. Connection details need to show where loads are supported and where movement is allowed.

Water Drainage, Air Leakage, and Thermal Performance 

A neat line of sealant on the outside does not tell the whole story about rainwater control. In drained systems, outer seals limit water entry, while internal drainage paths allow incidental water to escape back outside. Inner seals help restrict air leakage. These details vary between systems, and the appearance of an external joint alone cannot confirm how well the wall will perform.

Protection must also continue where the curtain wall meets a roof, sill or adjacent cladding. Gaps at these junctions can compromise the enclosure, even if the glazing itself is properly detailed.

Rainwater is only part of the facade's performance. Insulating glass units (IGUs) use multiple panes separated by a sealed space to reduce heat transfer. Low-E coatings reduce radiative heat transfer, while suitable solar-control coatings limit incoming solar energy. Thermal breaks reduce heat conduction through aluminum framing.

The framing and glass edges also contribute to whole-system thermal performance. NFRC's Component Modeling Approach evaluates non-residential fenestration using glazing, framing and edge-seal components. When reviewing a curtain wall specification, check whether the stated U-factor represents the complete assembly or only the glass.

Air and water control layers need to remain continuous across these junctions, a principle also emphasized in the Whole Building Design Guide (WBDG). Where site verification is required, AAMA 503-24 provides a specification for field testing newly installed curtain walls for air leakage and water penetration. Laboratory results alone cannot establish how well every interface has been installed.

Stick-Built vs. Unitized Curtain Walls 

Unitized Curtain Walls 

With stick-built curtain walls, installers assemble the framing members on site before glazing and sealing the joints. Much of the work takes place directly on the building, where crews need access across the facade. Labor availability and weather exposure also affect how the installation is planned.

Unitized curtain walls shift much of that assembly into a factory. Larger framed units are assembled and typically glazed before delivery, leaving installers to attach them to the building and complete the connections between units. There is less assembly work on site, but fabrication, transport and lifting arrangements still require careful coordination.

Factory assembly brings some decisions forward. Panel dimensions, interfaces and connection requirements must be settled before units enter production. Repeated modules make the production sequence easier to organize; late changes can interrupt it. Neither method is automatically faster or cheaper. The actual facade layout and construction conditions still need to guide the comparison.

Structural glazing is a separate distinction. It describes how glass is attached, not where the curtain wall is assembled. A unitized system can use structural silicone glazing or visible retaining caps, so keep the assembly method and glazing method separate when comparing proposals.

Where Are Glass Curtain Walls Used? 

 Glass Curtain Wall application

Office buildings, hotels, commercial developments and public buildings use glass curtain walls for extensive glazing and continuous exterior elevations. They can enclose areas across multiple floors, combining transparent openings with opaque zones at floor edges. Within that enclosure, the glazing needs to serve the spaces behind it.

A lobby may prioritize views and a strong connection to the entrance. An office facade also needs to account for workstations, screens and hours of direct sun. Similar glass areas can therefore require different combinations of light transmission, solar control and shading. More daylight does not automatically mean better visual comfort.

Application condition Design direction
Glazed elevations continuing across floor levels Coordinate vision areas, opaque spandrels, floor edges and structural connections.
Office spaces with extended occupancy Balance daylight and views with glare control, solar gain and shading.
Lobbies and entrances emphasizing outward views Position framing and opaque areas around the sightlines the design needs to preserve.

Repetition does not require identical glass specifications throughout the building. Two elevations can share the same panel dimensions while receiving different solar exposure. The team may need to retain the framing pattern but adjust the glazing or shading. Where appearance must remain consistent, review samples of the proposed glass configurations together before ordering.

Conclusion

A glass curtain wall does more than create a transparent building exterior. Its framing, anchors, glazing and seals work together to transfer loads, accommodate movement and control weather exposure. Whether stick-built or unitized, the system must suit the facade layout, building conditions, and installation requirements.

Where glass curtain walls meet architectural metal panels, early coordination helps avoid problems at the adjoining interfaces. PRANCE supports architectural metal panel design and production. Contact PRANCE experts for a quotation on the metal elements of your facade.

FAQs

What Is the Difference Between a Curtain Wall and a Storefront?

Storefront framing commonly serves ground-floor and low-rise applications. Curtain walls can extend across multiple floors with corresponding support and movement provisions. Similar sightlines do not establish equivalent performance. If the required spans, movement or weather resistance exceed a storefront system’s documented capabilities, assess a suitable curtain wall system. Building height alone does not establish suitability.

Can a Glass Curtain Wall Include Metal Panels?

Yes. Metal infill panels can form opaque areas within a curtain wall, including spandrel zones. Their supports, seals and any insulation must suit the selected assembly. A separate metal cladding system beside the curtain wall needs a coordinated interface. Confirm which arrangement the drawings show, because the two approaches involve different connection and weatherproofing details.

Can Curtain Walls Have Opening Windows?

Yes, some systems accommodate integrated operable windows or vents. The opening unit needs compatible framing, seals and hardware, with performance appropriate to the project. Confirm the proposed configuration with the system supplier early. Adding an opening later can affect framing layout and fabrication, and ventilation needs should also align with the building’s mechanical strategy.

What Is the Difference Between Stick-Built and Unitized Curtain Walls?

Stick-built curtain walls are assembled on site, with framing members installed before glazing and sealing. Unitized curtain walls use larger, factory-assembled and typically pre-glazed units that are installed as complete sections. Stick-built systems require more on-site assembly, while unitized systems depend more on factory fabrication, transport and lifting coordination. The suitable method depends on the facade layout and construction conditions.

prev
How to Improve Auditorium Acoustics and Where Wall Panels Fit
Curtain Wall Components: What Are the Main Parts?
next
recommended for you
Interested?
Request a call from a specialist
Tailor-make profect solutions for your metal ceiling & wall projects. Get a complete solution for customized metal ceiling & wall projects. Receive technical support for metal ceiling & wall design,installation & correction.
Architectural Solutions
Customized For You
Surface Finishes & Color Charts
Contact Info
Tel: +86-757-83138155
Tel/Whatapps: +86-13809708787
Fax: +86-757-83139722

Factory and Showroom: 169, South Area, Base of Electrical and Electronic lndustry, Baini, Sanshui, Foshan, Guangdong.
Are you interested in Our Products?
We can customize installation drawings specifically for this product for you. Please contact us.

*We will reply within 24 hours. If you don't receive our email, please check your spam folder. For urgent inquiries, please reach out via WhatsApp: +86-13809708787

* Kindly ensure your email and phone number are correct so our specialist can reach you promptly, or you can send a message to our whatsapp +86-13809708787

弹窗效果
Customer service