PRANCE metalwork is a leading manufacturer of metal ceiling and facade systems.
A crate is the last thing the factory builds. It decides whether everything else survives.
Weeks of careful coating, cutting and folding can be undone in the forty minutes it takes a forklift to unload a container on a rough site road, and the only thing standing between finished panels and that forklift is a box of timber, foam and film that most buyers never look at until it arrives broken.
So look at it before it ships.
Good metal wall panel export packaging is engineered, not improvised. This guide covers how crates are designed, what international rules apply to them, and the details that separate packaging that protects from packaging that merely contains.
Packaging has to survive every leg of the trip. Not only the sea.
A typical export route includes a truck to the port, container handling at two terminals, weeks at sea, customs inspection, another truck and finally unloading on site, often onto uneven ground with whatever lifting equipment happens to be there. Each stage brings a different risk, from vibration and stacking loads to tipping, rain and repeated forklift handling.
Write those stages down. Then design for the worst one.
Yes, solid wood crates, pallets and dunnage must be treated and carry the IPPC mark under ISPM 15.
Most export crates are timber. Timber crossing borders is regulated.
ISPM 15, the international standard for regulating wood packaging material in trade, requires solid wood packaging such as crates, pallets and dunnage to be treated against pests and marked with the official IPPC mark. Approved treatments include heat treatment, marked HT, and fumigation. Untreated or unmarked wood can be refused, treated at the buyer’s cost or destroyed at the destination port, sometimes with the panels still inside.
Processed wood such as plywood, OSB and particleboard is exempt, which is why many exporters build crate walls from plywood on treated solid timber bases.
Every solid wood component carries a legible IPPC mark
The mark shows the treatment code and the producer number
Dunnage and bracing used inside the container are treated too
Plywood panels are genuine processed wood, not solid boards
Different panels suit different containers.
| Packaging type | Best for | Strengths | Watch for |
|---|---|---|---|
| Closed plywood crate | Finished flat and folded panels | Full protection, stackable | Weight and moisture inside |
| Open timber frame crate | Large, robust panels | Lighter, easy inspection | Less protection from impact |
| Steel A-frame or rack | Long or heavy panels, repeat shipments | Strong, reusable | Return logistics and cost |
| Cartons on pallets | Small trims and accessories | Light, cheap | Crushing under stacking |
Most shipments of sheet metal wall panels use closed plywood crates for finished panels and smaller boxed packs for trims, closures and fixings, all labeled to the same system.
Smaller stiff panels can travel flat, while larger or folded panels usually travel better on edge with continuous support.
Orientation matters as much as the box.
Flat stacking keeps packing simple. On edge is safer for anything large, supported along its length, because flat stacks put the full weight of the upper panels on the lowest ones and can mark or bend them.
Each panel needs continuous support, not just contact at its corners. Internal frames, foam blocks and padded cross members hold panels still so they cannot slide, rock or flex in transit.
No finished face should touch another surface. Interleaving sheets or foam between every panel, and edge protectors on folds and corners, keep faces apart. Friction damage inside the container is mostly a separation failure, and it is covered in detail in a separate guide.
Film goes on before packing, over every finished face and return, applied in clean conditions so no grit sits beneath it.
Moisture damages finishes quietly.
Crates sealed completely in plastic can trap humidity, which condenses as temperatures swing between day and night or between climates. A better approach uses a breathable wrap or a moisture barrier with desiccant packs inside, dry timber, and drainage gaps in the crate base so any water that enters can leave.
Wet timber is a hidden risk. It releases moisture for weeks after packing.
A crate must carry its own load and the crates stacked on top.
Design the base and frame for the full packed weight plus stacking, mark the maximum stacking height, and provide forklift entry on the sides that will face unloading. For heavy crates, add clear lifting points and mark the center of gravity. Crate sizes should also suit the container, and fitting crates to a 40ft box well reduces both freight cost and movement inside the load.
Every crate should carry its number, zone, contents, weight, stacking limits and ISO 780 handling symbols.
A crate that cannot be identified cannot be unloaded efficiently.
Project name, crate number and installation zone on at least two faces
Contents summary and gross weight
Handling symbols to ISO 780, such as this way up, fragile, keep dry and center of gravity
Maximum stacking marks
A packing list inside the crate and a copy with the shipping documents
Tilt and shock indicators on high-value crates show at arrival whether a crate was dropped or laid on its side somewhere along the way. They do not prevent damage. They make claims far easier.
Packaging can be tested before it is trusted.
Distribution testing programs such as those published by the International Safe Transit Association simulate vibration, drops and compression on packed products, and some buyers require them for new crate designs or high-value finishes. Even without formal testing, a trial shipment or a factory drop and tilt check on a first crate catches weak points early.
At PRANCE, we design crate layouts with the transport route in mind, not just the panel sizes.
For the TRX sales center in Baghdad, road and sea transport conditions were studied before shipping so that crates could survive both the ocean leg and the overland delivery that followed. That same thinking applies on every export job. If the last fifty kilometers are rough, the crate is built for them.
Packaging details belong in the wider plan too. Export packaging inside the procurement plan should be agreed before production, since crate design affects freight cost, site handling and who carries the risk of damage.
Export packaging is part of the product.
Plan for every leg of the journey, use ISPM 15 compliant wood, choose the right crate type, support and separate every panel, control moisture, mark crates clearly and test new designs before trusting them with a full shipment. Done properly, the crate is forgotten the moment it is opened, because everything inside looks exactly as it did at the factory. Ask PRANCE for export packaging details for your project.
ISPM 15 is the international standard for wood packaging material in trade. It applies to solid wood crates, pallets and dunnage, which must be treated and carry the IPPC mark.
Yes. Processed wood such as plywood, OSB and particleboard is exempt, which is why many export crates use plywood walls on treated solid timber bases.
It depends on size and stiffness. Smaller stiff panels can travel flat, while larger or folded panels often travel better on edge with continuous support.
Use dry timber, breathable wraps or moisture barriers with desiccants, and drainage gaps in the crate base. Avoid fully sealed plastic that traps condensation.
Handling symbols to ISO 780, such as this way up, fragile, keep dry and center of gravity, plus crate number, zone, weight and stacking limits.
*We will reply within 24 hours. If you don't receive our email, please check your spam folder. For urgent inquiries, please reach out via WhatsApp: +86-13809708787
* Kindly ensure your email and phone number are correct so our specialist can reach you promptly, or you can send a message to our whatsapp +86-13809708787